The Beko TSE1284N is a freestanding freezer with a total gross capacity of 128 liters, featuring manual defrost, adjustable thermostat, fast freeze function, interior light, and reversible door. Designed for household use, it operates on 220-240V, 50Hz. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.
Key components: Freezer cabinet, adjustable thermostat control knob, fast freeze switch, interior light, adjustable feet, reversible door hinges, and wire shelves.
| Feature | Description |
|---|---|
| Total Gross Capacity | 128 liters |
| Defrosting Type | Manual defrost |
| Energy Class | As per local regulations |
| Fast Freeze Function | Rapidly lowers temperature for new food |
| Adjustable Thermostat | Controls internal temperature |
| Interior Light | Illuminates interior when door is open |
| Reversible Door | Door can be hinged on left or right side |
| Adjustable Feet | For leveling the appliance |
| Wire Shelves | Adjustable storage compartments |
| Power Supply | 220-240V, 50Hz |
Unpack and inspect contents. Place on a flat, stable floor.
WARNING! Do not install near ovens, radiators, or in direct sunlight. Ensure proper ventilation.
Before first use, clean the interior and let the freezer run empty for 2-3 hours.
CAUTION! Do not load food until the freezer has reached the desired temperature (approx. -18°C).
Control panel located inside or on the front of the freezer.
Thermostat Knob: Rotate to set temperature (1 = warmest, 5 = coldest). Middle setting (3 or 4) is recommended for normal operation.
Fast Freeze Switch: Press to activate. The Fast Freeze indicator light will illuminate. This function runs the compressor continuously to rapidly lower the temperature. Deactivate after 24 hours or when food is frozen.
Interior Light: Automatically turns on when the door is opened.
Door Open Alarm (if equipped): Sounds if the door is left open for more than a few minutes.
Proper use ensures efficient operation and food preservation.
Tip: Label packages with contents and date to keep track of storage time.
Manual defrost is required when frost layer exceeds 5 mm thickness.
WARNING! Never use electrical appliances inside the freezer to speed up defrosting. Do not pour water over the freezer.
Regular maintenance ensures long life and optimal performance.
Monthly: Check door seals for dirt or damage. Clean if necessary.
Every 6 Months: Clean the condenser coils at the back of the appliance with a brush or vacuum cleaner (ensure the appliance is unplugged).
As Needed: Defrost when frost exceeds 5 mm. Clean interior and exterior.
CAUTION! Always unplug the appliance before any maintenance. Do not use steam cleaners.
This appliance complies with relevant EU Directives and UK regulations. The refrigerant (R600a) is flammable. Do not damage the cooling circuit. At end of life, dispose of the appliance according to local WEEE (Waste Electrical and Electronic Equipment) regulations. Contact your local authority for recycling information. For support, visit www.beko.com or contact your local Beko service center.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Freezer does not run | No power / Thermostat at "0" | Check if plugged in. Check circuit breaker. Set thermostat to position 3 or 4. |
| Temperature too high | Door left open / Overloaded / Faulty seal | Ensure door is closed properly. Do not overload. Check and clean door gasket. |
| Excessive frost build-up | Frequent door opening / Warm food / Faulty seal | Minimize door openings. Cool food first. Check door seal. |
| Unusual noise | Appliance not level / Items touching interior walls | Level the appliance using adjustable feet. Rearrange contents. |
| Interior light does not work | Bulb burnt out | Replace with a bulb of the same type and rating (consult manual). |
| Water pooling inside or under freezer | Drain hole blocked (if equipped) / Defrost water not contained | Clean the drain hole with a pipe cleaner. Ensure container is placed during defrosting. |
Reset: Turn thermostat to "0", unplug for 5 minutes, then plug back in and set to desired position.
Service: For issues not resolved above, contact authorized Beko service. Do not attempt to repair the refrigerant system yourself.